7014 vs 7018 welding rod

7014 vs 7018 welding rod

When it comes to welding mild steel or low to medium carbon steel, two of the most popular electrodes that come to mind are E7014 and E7018.

Both of these electrodes are for stick welding or shielded metal arc welding (SMAW). However, there are some key differences between these two rods that make them better suited for certain applications & give them special features.

In this blog post, we will take a closer look at the similarities and differences between E7014 and E7018 welding rods, and help you to determine which one is the best choice for your specific welding need.

7014 vs 7018

7014 vs 7018 Specification

E7014 and E7018 welding rods are both types of shielded metal arc welding (SMAW) electrodes, which are used for welding low carbon steel. Both of these electrodes are covered by the AWS A5.1 specification, which covers carbon steel electrodes for shielded metal arc welding.

Read more: Different versions of E7018 Welding Rod:

7014 vs 7018 Chemical Compositions

Both E7014 and 7018 has similar chemical compositions except that 7018 has a higher Manganese content of 1.60% but a lower silicon content of 0.75% compared to 7014 (Manganese-1.25% & Silicon-0.90%).

Read more: E7014 Welding Rod: Everything you need to know about it.

Complete chemical compositions comparison of 7014 and 7018 welding rod are given in the below table as required by AWS A5.1 specification.

Chemical ElementE7014 Composition (%)E7018 Composition (%)
Carbon (C)0.15 max0.15 max
Silicon (Si)0.90 max0.75 max
Manganese (Mn)1.25 max1.60 max
Sulfur (S)0.035 max0.035 max
Phosphorus (P)0.035 max0.035 max
Nickel (Ni)0.30 max0.30 max
Chromium (Cr)0.20 max0.20 max
Molybdenum (Mo)0.30 max0.30 max
Vanadium (V)0.08 max0.08 max
Total of Mn+Ni+Cr+Mo+V1.50 max1.75 max

7014 vs 7018 Tensile Strength & Mechanical Properties Comparison

both E7014 and E7018 welding rods have similar tensile and yield strength. However, E7018 has a higher elongation of minimum 22% compared to E7014 which has a minimum elongation of 17%.

See also  Stress Relief in Welding

While 7018 welding rod has a weld toughness requirement of 15 ft·lbf at –20°F (20 J at –30°C), toughness requirements for E7014 welding rod are not specified in the AWS A5.1 specification.

PropertyE7014 ValueE7018 Value
Tensile Strength70 Ksi (490 MPa) min70 Ksi (490 MPa) min
Yield Strength58 Ksi (400 MPa) min58 Ksi (400 MPa) min
Elongation17% min22% min
ToughnessNot specified15 ft·lbf at –20°F (20 J at –30°C),

7014 vs 7018 Polarity

E7014 and E7018 welding rods have different polarity. E7014 electrode is typically used in the DC+ (Direct Current Electrode Positive), DC- (Direct Current Electrode Negative), & AC polarity. On the other hand, E7018 electrode is typically used in the DCEP (Direct Current Electrode Positive) & AC polarity only.

Read more: Science behind the Welding Polarity & their types.

In summary, E7014 can be used with all welding polarity while 7018 is used only with DCEP and AC polarity.

7014 vs 7018 Coating difference

  • E7014 and E7018 welding rods have different coatings.
  • E7014 electrode coating is made of titania with added iron powder.
  • E7018 welding rod coating is made of low hydrogen potassium with added iron powder.

7014 vs 7018 Welding Positions

E7014 and E7018 welding rods can be used for welding in all positions, but they are known to perform better in certain positions. The third digit “1” in both rods mean that they can be used with all position welding applications for pipe, plate or any other material form.

See also  ER80S-B2 TIG- MIG Wire: What You Need to Know

7014 vs 7018 Slag Characteristics

E7014 electrode is known for its good bead appearance and easy slag removal. The slag created by E7014 is easily removed by using a chipping hammer or wire brush. This electrode is typically used for welding in all positions and for creating a good bead appearance.

E7018 electrode is known for its deep penetration and high strength. The slag created by E7018 is more difficult to remove than that created by E7014. The slag is harder, thicker, and more tenacious than the slag created by E7014.

This electrode is typically used for welding in all positions, and for high strength and deep penetration. A complete summary of Differences between E7018 and E7014 welding rods are:

Table 6, E7018 vs. E7014 Welding Rod
Rod Characteristics E7018 E7014
 AWS Specification  AWS A5.1  AWS A5.1
 Classification  E7018  E7014
 Coating types   Low hydrogen Potassium with added Iron Powder Iron Powder titania
 Tensile & Yield Strength (Ksi)  70 & 58  70 & 58
 Polarity  AC, DCEP  AC, DCEN & DCEP
 Welding Position  All  All
 Weld penetration  Medium Low to Medium
Slag Thick slag
Medium,  very easily removable slag
 Arc features Smooth arc smooth, quiet arc
 Application  Fillet, fill & cap passes high deposition applications

7014 vs 7018 Applications

E7014 electrode is typically used for welding in all positions and for creating a good bead appearance and easy slag removal.

See also  ENiCrMo-3 Welding Electrode

The main applications of E7014 welding electrode are:

  • Construction, shipbuilding, and maintenance and repair work.
  • Welding low carbon steel.
  • Repair and maintenance of equipment.
  • Construction of new equipment.

E7018 electrode is typically used for welding in all positions, and for high strength and deep penetration. It is commonly used for welding low carbon steel and for applications such as structural steel fabrication, pressure vessels, and heavy equipment repair.

E7018 is also used in the fabrication of bridges, buildings, and other structures that require deep penetration and high strength. E7018 welding rod is known for its deep penetration and high strength, which makes it well-suited for the following applications:

  • Welding in flat and horizontal positions.
  • Structural steel fabrication.
  • Pressure vessels.
  • Heavy equipment repair.
  • Fabrication of bridges, buildings, and other structures that require deep penetration and high strength.
  • Welding low carbon steel.
  • All position welding.

Related Posts:

FAQS

What is the main difference between E7014 and E7018 welding rods?

The main difference between E7014 and E7018 electrode is the coating type. 7018 rod has basic coating and good for impact applications, while 7014 is not.

What are the applications of E7014 and E7018 welding rods?

E7014 is best suited for welding in vertical and overhead positions, construction, shipbuilding, and maintenance and repair work, while E7018 is best suited for welding in flat and horizontal positions, structural steel fabrication, pressure vessels, and heavy equipment repair.

Can E7014 and E7018 welding rods be used in all positions?

Both E7014 and E7018 welding rods can be used in all positions, but they perform better in certain positions based on their characteristics.

Are E7014 and E7018 welding rods shielded by the flux coating?

Yes, both E7014 and E7018 welding rods are shielded by the flux coating, so they don’t require any additional shielding gas.

Material Welding is run by highly experienced welding engineers, welding trainers & ASNT NDT Level III bloggers. We strive to provide most accurate and practical knowledge in welding, metallurgy, NDT and Engineering domains.